Error Cod 0060510 Unable to Connect Tothe Server Please Try Again Later

Message (Back up Code) Appears

This section describes some of the letters that may appear.

Annotation

• A support code (error number) is displayed for some errors. For details on errors that have support code, run into List of Support Code for Mistake.

If a bulletin appears on the printer's LCD, see below.

• Message Appears on Printer's LCD

If a message appears on the figurer, run across below.

• Fault Regarding the Paper Thickness Lever Is Displayed (Windows)
• Error Regarding Ability Cord Being Unplugged Is Displayed (Windows)
• Writing Error/Output Error/Communication Error (Windows)
• Other Error Messages (Windows)

Bulletin Appears on Printer's LCD

Check the message and have an appropriate activity.

• Ability was not turned off correctly the terminal time. Printing when turning ability off.

  While the ability was still on, the printer may accept been unplugged or the bombardment ability supply may accept stopped by the exhausted battery.

  Press the printer'south OK button to abolish the error.

  Note

  • See Unplugging the Printer to unplug the power string correctly.
  • See Using the Battery for how to utilize the battery.

• Cannot connect to the server. Please look a while and attempt again.

  The printer cannot connect to the server due to a advice error.

  Press the printer's OK button to abolish the mistake and try once again afterwards a while.

Error Regarding the Paper Thickness Lever Is Displayed (Windows)

The proper position of the paper thickness lever varies depending on the type of paper you are printing on.

Set up the paper thickness lever to the left when printing on envelopes. Set the paper thickness lever to the right when printing on newspaper other than envelopes.

Adjust the position of the paper thickness lever properly, so click OK on the screen.

Error Regarding Power String Being Unplugged Is Displayed (Windows)

While the power was withal on, the printer may have been unplugged or the battery power supply may have stopped by the wearied battery.

Check the mistake message that appears on the estimator and click OK.

The printer starts printing.

Annotation

• Meet Unplugging the Printer to unplug the power cord correctly.
• Encounter Using the Battery for how to use the bombardment.

Writing Fault/Output Fault/Communication Fault (Windows)

1. Check1 If ON lamp is off, press printer'due south ON push button.

   The ON lamp flashes while the printer is initializing. Wait until the ON lamp stops flashing and remains lit.

2. Check2 Brand sure printer is properly continued to reckoner.

   If you are using a USB cablevision, brand sure information technology is securely connected to both the printer and the computer. When the USB cable is securely plugged in, check the following:

   • If you are using a relay device such as a USB hub, disconnect it, connect the printer straight to the computer, and retry the press. If printing starts usually, there is a problem with the relay device. Contact the vendor of the relay device.
   • There could as well be a trouble with the USB cable. Replace the USB cable and retry the press.

   If yous employ the printer over a LAN, brand sure the printer is correctly set up for network use.

3. Check3 Make certain Printer Driver is installed correctly.

   Uninstall the Printer Driver following the process described in Deleting the Unnecessary Printer Commuter and click here to reinstall it.

4. Check4 When printer is continued to your computer with a USB cable, bank check device status from your computer.

   Follow the procedure below to check the device condition.

   1. Select Command Console > Hardware and Sound > Device Managing director.

      Note

      • If the User Account Control screen appears, select Continue.

   2. Open USB Press Back up Properties.

      Double-click Universal Serial Coach controllers and USB Printing Back up.

      Annotation

      • If USB Printing Support Properties screen does not appear, make sure the printer is correctly connected to the reckoner.

        • Check2 Make certain printer is properly connected to computer.

   3. Click Full general tab and check for a device trouble.

      If a device error is shown, come across Windows Help to resolve information technology.

Other Error Messages (Windows)

1. Cheque If an mistake message appears outside printer status monitor, check the post-obit:

   • "Could not spool successfully due to insufficient disk infinite"

     Delete whatsoever unnecessary files to increase the amount of gratis space on the disk.

   • "Could not spool successfully due to insufficient retentiveness"

     Shut other applications to increase the available retention.

     If you still cannot impress, restart your computer and retry the printing.

   • "Printer driver could not be found"

     Uninstall the Printer Commuter post-obit the procedure described in Deleting the Unnecessary Printer Driver and click here to reinstall it.

   • "Could not impress Application name - File proper name"

     Try printing again once the electric current job is complete.

bishopsenifee.blogspot.com

Source: https://ij.manual.canon/ij/webmanual/ErrorCode/TR150%20series/EN/ERR/err_t_07_02.html?ref=err_t_07_02

Share this post